Envelope, mechanical and fire-rated insulation for Sunrise offices, retail, restaurants, hotels, medical buildings, warehouses and cold storage — including night and weekend work in occupied space.
Commercial insulation in Sunrise is a scheduling problem as much as a technical one. The building is usually occupied, the tenant is usually open, and the work has to happen without shutting anything down. We run night and weekend crews in Broward County for exactly this reason, with containment, HEPA filtration and a clean handover before the doors open.
The scopes are different too. A Sunrise commercial job routinely combines envelope insulation, mechanical insulation on duct and pipe, and fire-rated assemblies in the same building, each inspected against a different part of the code. Splitting those across three subs is how schedules slip. We carry all three, which is usually why a Broward County GC calls us rather than a residential outfit that also does commercial.
Sunrise sits in Florida Climate Zone 1 — the hottest, most humid zone in the continental United States. Under the Florida Building Code, Energy Conservation (8th Edition), the ceiling minimum here is R-30 and framed walls are R-13. ENERGY STAR recommends R-30 for an uninsulated attic in this zone; we build to R-38 as the practical target.
| Item | Value | Where it applies |
|---|---|---|
| Building envelope | Roof, wall and floor assemblies to the FBC commercial energy provisions | New build and retrofit |
| Mechanical | Duct wrap, duct liner, pipe and equipment insulation | Occupied and new construction |
| Fire-rated | Rated assemblies, safing, and firestopping at penetrations | Multi-tenant and life-safety scopes |
| Metal building | Faced systems, liner systems and closed-cell for vapor control | Warehouse, industrial, agricultural |
We take off from drawings and confirm assemblies against the specified code path before pricing.
For occupied Sunrise buildings we agree the phasing, access hours and containment plan with the property manager up front.
Containment, HEPA filtration and floor protection go in before any material moves.
Envelope, mechanical and fire-rated scopes installed and documented per assembly.
We attend inspections, supply submittals and product data, and hand over close-out documentation.
Commercial insulation in Sunrise is priced by scope rather than by a per-square-foot rule of thumb. Warehouse and metal building envelope work commonly runs $1.75 to $4.50 per square foot; mechanical and fire-rated scopes are quoted by linear foot and assembly.
Not sure commercial insulation is the right call? These are the other scopes we run in Sunrise — and the Sunrise insulation overview covers the whole envelope.
Open-cell and closed-cell polyurethane foam that air-seals and insulates in one application — installed on roof decks, walls, and crawl spaces throughout Sunrise.
Spray Foam Insulation in Sunrise →Loose-fill fiberglass or cellulose blown to a consistent, verified depth across Sunrise attic floors — the fastest way to bring an under-insulated attic up to code.
Blown-In Insulation in Sunrise →Pre-cut fiberglass and mineral wool batts fitted between studs, joists and trusses in Sunrise homes, additions, garages and light commercial framing.
Batt Insulation in Sunrise →HEPA-filtered vacuum removal and disposal of wet, contaminated, storm-damaged or rodent-infested insulation from Sunrise attics, walls and crawl spaces.
Insulation Removal in Sunrise →Attic, wall, floor and air-sealing work for Sunrise houses, condos and townhomes — the whole envelope handled by one contractor instead of four.
Residential Insulation in Sunrise →Commercial insulation in Sunrise is priced by scope rather than by a per-square-foot rule of thumb. Warehouse and metal building envelope work commonly runs $1.75 to $4.50 per square foot; mechanical and fire-rated scopes are quoted by linear foot and assembly. Standard Insulation gives free written itemized estimates throughout Sunrise and Broward County — call (561) 975-6204.
Sunrise sits in Florida Climate Zone 1 — the hottest, most humid zone in the continental United States. The Florida Building Code, Energy Conservation (8th Edition) sets a R-30 minimum for ceilings in this zone, and R-38 is the practical target for comfort and utility savings. Many Sunrise homes built before 2005 still measure R-11 to R-19, which is a large part of why their summer bills run high.
Insulation-only retrofits in Broward County usually do not require a permit, but new construction, additions and commercial work do, and the requirement is set locally rather than statewide. We confirm with the Broward County building department before we start, and we link to their site below so you can check for yourself.
Yes. Standard Insulation is a licensed Florida insulation contractor carrying general liability and workers' compensation coverage, and we work throughout Sunrise and all of Broward County. Certificates of insurance are provided to homeowners, general contractors and property managers on request before any work begins.
We answer the phone 24 hours a day, 7 days a week. In Broward County we can usually be on site for a free assessment within 24 to 48 hours, and emergency insulation removal after a roof leak or storm gets same-day priority whenever we can make it happen.
Most Sunrise residential jobs are completed in a single day. Larger homes, full removals and commercial scopes in Broward County run two to four days. We give you a firm window before we start and we call if anything changes.
Cooling is roughly half of a typical Sunrise electric bill. Bringing an under-insulated attic up to a properly air-sealed R-38 commonly cuts the cooling portion by 20 to 30 percent — more if your ductwork runs through the attic. On a $300 summer bill that is usually $30 to $45 a month back.
These are the outside sources we work from. None of them are ours — check them yourself before you sign anything with any contractor.
Written, itemized, and no obligation. We answer the phone 24 hours a day.
Request your free estimate 📞 (561) 975-6204
More about Commercial Insulation statewide · All Broward County locations · Insulation blog
